routing

  1. Rastko

    lagg0 denies router config

    Hi, I have set up the lagg0 failover virtual link that aggregates ethernet and radio adapters on my laptop. Everything works fine, except I cannot access my router configuration page. I've changed the firewall script to use interface "lagg0" in the rules, but I didn't change much, and the...
  2. fullauto2012

    Solved Geteway not forwarding

    root@gateway:/usr/home/tim.falardeau # netstat -rn Routing tables Internet: Destination Gateway Flags Netif Expire default xx.xx.xxx.90 UGS em0 xx.xx.xxx.88/30 link#1 U em0 xx.xx.xxx.89 link#1 UHS...
  3. andrewm659

    routing in jails

    Not sure this is the right part of the forums. Move it if necessary. I have my FreeBSD 11 server running jails (ezjail) and I just moved it to a new VLAN. Most everything inbound works. I have for example rancid setup in one of the jails. Works great. But since I moved it to a new VLAN...
  4. whoops

    ipv6 -host route to on-link gateway fails

    I've successfully reinstalled my OVH VPS with FreeBSD, so I'm well into unsupported territory here. Before reinstalling I did verify IPv6 works as expected under Linux. OVH's IPv6 configuration is a bit interesting. You can find the full instructions here, but the short version is: IP...
  5. S

    ECMP failover

    Hi! I have remote network which is routed via two gateways (RADIX_MPATH in kernel): Routing tables Internet: Destination Gateway Flags Netif Expire 192.168.11.0/24 10.0.0.2 UGS ngeth1 192.168.11.0/24 10.0.0.6 UGS ngeth2 All works fine...
  6. M

    Userland ppp routing problem

    I have noticed a difference in behavior between ppp on FreeBSD 9.3 and FreeBSD 10.2 in what routes are added when a PPPoE session comes up. I have been using this configuration since FreeBSD 7+ My config with secrets and public IPs changed is as follows: default: set log Phase Chat IPCP CCP...
  7. IPTRACE

    No packets between hypervisor interface and guest

    I don't have traffic back between router and vm1. I've set pass all with logs enabled to see better packets flow. FreeBSD BOX: hypervisor vm1: VM guest router: wifi router gateway igb2: 192.168.1.1 bridge0: 10.0.0.1 tap0: 10.0.0.18 router: 192.168.1.2...
  8. S

    Slow uploading speed

    Hi, We're facing quite slow uploading speed on FreeBSD-10.X both over HTTP (NGINX) & over FTP. Hardware is quite strong with 4x1Gbps LACP / 65G RAM / 12x3TB SATA . There's not much load over HDDs so i suspect that maybe tcp tuning has some problem. Here is my sysctl.conf...
  9. Kalero

    Solved Can not ping from a VMware VM with FreeBSD 11.0-RELEASE @ OVH (hosting company)

    Hi people, I'm trying to set up a server with FreeBSD 11.0-RELEASE on a VMware VM @ OVH (hosting company) but, when I try to ping, I get a "host name lookup failure". It's very strange because I copied /etc/rc.conf and /etc/resolv.conf from the previous working installation with FreeBSD...
  10. ClayS

    Bridging problems

    I am trying to share a single 10Gb ethernet outlet in my office between two machines by bridging across a FreeBSD server using the second port on its 10Gb card. The bridge works quite well, and the other machine gets network service. The FreeBSD server, however, does not, even though I added an...
  11. bMalum

    IPv6 Jail Setup and Routing

    Hi everyone, Short: I want in FreeBSD Jails with Private IPv4-Addresses and Global Scope IPv6 Addresses. But iI can't get it to work. I have tried a lot, so iI can only tell you what iI have tried. For me it is possible to add an interface alias to re0 and I'm also able to ping it from around...
  12. GreenX

    Is it possible to source-based routing without the use of PF?

    The situation is as follows: there is a server for multiple services. Services put in jail (for example: monitoring zabbix). In jails, gray addresses and a separate interface for them, and internal networks. The main interface uses "white" ip address, but it is not so important. It is...
Back
Top