How do I properly add IPv6 IP addresses in my rc.conf file in FreeBSD 11.1?
I was assigned a /64 to my server. Also, how do I apply the changes without rebooting? /etc/netstart ?
This is how I am adding them now (IP address has been modified for security) ...
Hi, wondering if I can get a bit of help with IPv6.
Following instructions in FreeBSD Handbook have the following in /etc/rc.conf for IPv6:
ifconfig_em0_ipv6="inet6 accept_rtadv"
rtsold_enable="YES"
ipv6_defaultrouter="2607:xxxx:1001::1"
ifconfig_em0_ipv6="inet6...
Dear FreeBSD users,
My first IPv6 try with my FreeBSD desktop machine was a bit disappointing.
According to FreeBSD Handbook, I added two lines in my /etc/rc.conf:
ifconfig_re0_ipv6="inet6 accept_rtadv"
rtsold_enable="YES"
I added into my fully functional /etc/pf.conf:
icmp6_types = "{...
Hello *,
in my nsd.conf I have configured:
server:
# Number of NSD servers to fork. Put the number of CPUs to use here.
server-count: 1
ip-address: 31.220.7.66
ip-address: 2a00:1a28:1157:35c::8c7d
outgoing-interface: 2a00:1a28:1157:35c::8c7d...
Both host/guest are using FreeBSD 11.1, I created the VM using vm-byhbe.
This is host configurationhe host:
/etc/rc.conf
ifconfig_igb0_ipv6="inet6 2a01:4f8:150:84ec::1 prefixlen 64"
ipv6_activate_all_interfaces="YES"
ipv6_defaultrouter="fe80::1%igb0"
rtadvd_enable="YES"
/etc/rtadvd.conf...
Since a few weeks I'm having a problem with the IPv6 connectivity of my FreeBSD 11.0 server. There had been no software updates or configuration changes that I know of that could cause the problem.
The server only has IPv6 connectivity (incoming and outgoing) for a short time (approx. 40-80...
I've been trying to setup ssh exclusively over IPV6 but have run in to a few issues. These are the steps I'm following, theoretically this should just work. Which is why I'm baffled at this point. I researched a few guides going back to version 10.3 and the process seems to be as follows...
Hi,
I am using gif_interfaces for setting up a HE tunnel broker connection.
While everything still works I get this warning:
/etc/rc.d/netif: WARNING: $gif_interfaces is obsolete. Use $cloned_interfaces instead.
However simply renaming it to cloned_interfaces doesn't do the trick. My...
Probably I'm missing something obvious, but this is just my second box with IPv6, never have dealt with it before. I cannot add a default gateway:# route add -inet6 default xxxx:52c0:101::1
route: writing to routing socket: Network is unreachable
$ ifconfig
vtnet0...
Hey folks,
I'm in progress of migrating my centos openvpn dualstack server to freebsd.
I got a problem with ipv6 connection and im not shure what is the problem.
IPv4 is working fine through the tunnel. IPv6 icmp is possible, but nameservers are not reachable on :53 or anything else except via...
When I enable IPv6 for sendmail and an IPv6 mail connection is made:
milter_sys_read(greylist): cmd read returned 0, expecting 5
Milter (greylist): to error state
Milter: connect: host=[IPv6:2401:a400:2070:7d01:5d62:ec06:7dcb:ff3], addr=IPv6:2401:a400:2070:7d01:5d62:ec06:7dcb:ff3, temp failing...
I've successfully reinstalled my OVH VPS with FreeBSD, so I'm well into unsupported territory here. Before reinstalling I did verify IPv6 works as expected under Linux.
OVH's IPv6 configuration is a bit interesting. You can find the full instructions here, but the short version is:
IP...
In IPv4 land I can do something like this:
ifconfig tun0 create
ifconfig tun0 a.b.c.d e.f.g.h
ifconfig tun0 alias i.j.k.l e.f.g.h
ifconfig tun0 up
However in IPv6 land I get stuck:
ifconfig tun0 inet6 A:B:C:D::E F:G:H::I prefixlen /128
ifconfig tun0 inet6 alias J:K:L::M F:G:H::I prefixlen...
Currently, I have to substitute dual-dhclient for dhclient from FreeBSD base to get DHCPv6 addresses, SLAAC addresses, and IPv4 addresses.
Amazon EC2 configures dual-dhclient in /etc/rc.conf to support IPv6.
It would be ideal for dhclient from FreeBSD base to do the job of dual-dhclient.
Is...
Hello! My immediate goal is the installation of FreeBSD over a Remote SSH session. Prerequisite to that, I need to configure the network on the machine using a Live CD.
I’d like to configure IPv4 using DHCP and IPv6 through SLAAC in the same manner that bsdinstall does during a “normal” initial...
I'm currently running 11.0-RELEASE-p7 in one of those cheap 1€ aruba VPS machines servers for fun.
Their current control panel doesn't support ipv6 auto configuration therefore it must be configured manually.
I'm able to configure the ipv6, but I lost connectivity a few seconds after boot.
My...
Hello
I just placed my server running FreeBSD 11 in a data center which provides IPv4 and IPv6 connectivity....IPv4 is no problem of course...
For the IPv6 setup I've been giving this information:
Prefix: 2a02:xxx:xxxx::/48
Gateway: fe80::1
So I changed rc.conf to read...
I have a jail running and the network configuration is done by the host's /etc/jail.conf. The behavior is that when the jail boots, sshd listens to the correct ipv4 address listed in the /etc/ssh/sshd_config, however it doesn't listen to the ipv6 address. I did attempt to set it to :: to see if...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.