Raspberry Pi 4B CAN HAT support ?

B

blt2b

I got a Raspberry Pi 4B with a RS485 CAN HAT.
FreeBSD 14.0-RELEASE is working perfectly fine but I am not able to see / interact with my CAN HAT.. Is there a need to add some special parameters ? (I already added the ones from the documentation) or CAN HAT is not supported by FreeBSD ?

Thanks
 
Code: 
# dmesg | egrep -i can\|spi
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
regfix0: Cannot configure GPIO pin: 5
regfix0: Cannot register regulator.
regfix2: Cannot set GPIO pin: 6
regfix2: Cannot register regulator.
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
 
Thanks Starcat for your findings !

So it is definitely not instantiated correctly as I don't have anything either on dmesg, /dev or ifconfig..

I am wondering if something is missing in /boot/efi/config.txt

I tried that :
[all] arm_64bit=1 dtparam=audio=on,i2c_arm=on,spi=on dtoverlay=mmc dtoverlay=disable-bt dtoverlay=mcp2515-can0,oscillator=8000000,interrupt=25,spimaxfrequency=1000000 device_tree_address=0x4000 kernel=u-boot.bin [pi4] hdmi_safe=1 armstub=armstub8-gic.bin enable_uart=1
 
Thanks tingo .

I added both
rc_debug="YES" rc_info="YES"
to my /etc/rc.conf, here is the result :

---<<BOOT>>--- GDB: debug ports: uart GDB: current port: uart KDB: debugger backends: ddb gdb KDB: current backend: ddb WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance Copyright (c) 1992-2024 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 15.0-CURRENT #0 main-n269103-112783ebbc31: Thu Apr 4 05:48:15 UTC 2024 root@releng3.nyi.freebsd.org:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC arm64 FreeBSD clang version 17.0.6 (https://github.com/llvm/llvm-project.git llvmorg-17.0.6-0-g6009708b4367) WARNING: WITNESS option enabled, expect reduced performance. VT(efifb): resolution 592x448 module scmi already present! real memory = 4148158464 (3955 MB) avail memory = 4016869376 (3830 MB) Starting CPU 1 (1) Starting CPU 2 (2) Starting CPU 3 (3) FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs random: unblocking device. random: entropy device external interface kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> on ofwbus0 ofw_clkbus0: <OFW clocks bus> on ofwbus0 simplebus1: <Flattened device tree simple bus> on ofwbus0 simplebus2: <Flattened device tree simple bus> on ofwbus0 regfix0: <Fixed Regulator> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency regfix1: <Fixed Regulator> on ofwbus0 regfix2: <Fixed Regulator> on ofwbus0 regfix3: <Fixed Regulator> on ofwbus0 regfix4: <Fixed Regulator> on ofwbus0 simplebus3: <Flattened device tree simple bus> on ofwbus0 simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 gpiobus0: <OFW GPIO bus> on gpio0 gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 gpiobus1: <GPIO bus> on gpio1 regfix0: Cannot configure GPIO pin: 5 REGNODE_INIT failed: 6 regfix0: Cannot register regulator. clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency regfix2: Cannot set GPIO pin: 6 REGNODE_INIT failed: 6 regfix2: Cannot register regulator. mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gpioregulator0: <GPIO controlled regulator> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 31,32,33,34,35,36,37,38,39,40,41 on simplebus0 usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0 gpioc0: <GPIO controller> on gpio0 uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 uart0: console (115200,n,8,1) spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 spibus0: <OFW SPI bus> on spi0 spibus0: <unknown card> at cs 0 mode 0 spibus0: <unknown card> at cs 1 mode 0 sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 mmc0: <MMC/SD bus> on sdhci_bcm0 iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 27 on simplebus0 bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0 bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on simplebus0 gpioc1: <GPIO controller> on gpio1 fb0: <BCM2835 VT framebuffer driver> on simplebus0 fb0: keeping existing fb bpp of 32 fbd0 on fb0 WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 15.0. VT: Replacing driver "efifb" with new "fb". fb0: 592x448(592x448@0,0) 32bpp fb0: fbswap: 1, pitch 2368, base 0x3eaf5000, screen_size 1060864 sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff irq 79 on simplebus1 mmc1: <MMC/SD bus> on sdhci_bcm1 pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0 cpulist0: <Open Firmware CPU Group> on ofwbus0 cpu0: <Open Firmware CPU> on cpulist0 bcm2835_cpufreq0: <CPU Frequency Control> on cpu0 pcib0: <BCM2838-compatible PCI-express controller> mem 0x7d500000-0x7d50930f irq 80,81 on simplebus2 pcib0: hardware identifies as revision 0x304. pci0: <OFW PCI bus> on pcib0 pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci0 pci1: <OFW PCI bus> on pcib1 bcm_xhci0: <VL805 USB 3.0 controller (on the Raspberry Pi 4b)> irq 92 at device 0.0 on pci1 bcm_xhci0: 32 bytes context size, 64-bit DMA usbus0 on bcm_xhci0 genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on simplebus2 genet0: GENET version 5.0 phy 0x0000 miibus0: <MII bus> on genet0 brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto genet0: Ethernet address: d8:3a:cd:43:11:99 clk_fixed4: clock-fixed has no clock-frequency clk_fixed4: clock-fixed has no clock-frequency gpioled0: <GPIO LEDs> on ofwbus0 lock order reversal: (sleepable after non-sleepable) 1st 0xffff000000dd86c8 LED mtx (LED mtx, sleep mutex) @ /usr/src/sys/dev/led/led.c:295 2nd 0xffffa00001892c10 Raspberry Pi firmware gpio (Raspberry Pi firmware gpio, sx) @ /usr/src/sys/arm/broadcom/bcm2835/raspberrypi_gpio.c:250 lock order LED mtx -> Raspberry Pi firmware gpio attempted at: #0 0xffff000000529c70 at witness_checkorder+0xa78 #1 0xffff0000004bdee0 at _sx_xlock+0x70 #2 0xffff00000092c644 at rpi_fw_gpio_pin_set+0xe4 #3 0xffff0000001dfdf4 at led_create_state+0x15c #4 0xffff0000001a6d1c at gpioled_attach+0x294 #5 0xffff0000004f00ec at device_attach+0x3fc #6 0xffff0000004efc54 at device_probe_and_attach+0x80 #7 0xffff0000004f21c8 at bus_generic_new_pass+0x100 #8 0xffff0000004f2178 at bus_generic_new_pass+0xb0 #9 0xffff0000004f2178 at bus_generic_new_pass+0xb0 #10 0xffff0000004ecaec at bus_set_pass+0x50 #11 0xffff000000434be0 at mi_startup+0x1e0 #12 0xffff0000000008a8 at virtdone+0x68 uma_zalloc_debug: zone "malloc-64" with the following non-sleepable locks held: exclusive sleep mutex LED mtx (LED mtx) r = 0 (0xffff000000dd86c8) locked @ /usr/src/sys/dev/led/led.c:295 stack backtrace: #0 0xffff00000052a0e0 at witness_debugger+0x60 #1 0xffff00000052b374 at witness_warn+0x40c #2 0xffff0000007ef970 at uma_zalloc_debug+0x34 #3 0xffff0000007ef4fc at uma_zalloc_arg+0x30 #4 0xffff0000004855f0 at malloc+0x90 #5 0xffff0000009212c4 at bcm2835_firmware_property+0x48 #6 0xffff00000092c65c at rpi_fw_gpio_pin_set+0xfc #7 0xffff0000001dfdf4 at led_create_state+0x15c #8 0xffff0000001a6d1c at gpioled_attach+0x294 #9 0xffff0000004f00ec at device_attach+0x3fc #10 0xffff0000004efc54 at device_probe_and_attach+0x80 #11 0xffff0000004f21c8 at bus_generic_new_pass+0x100 #12 0xffff0000004f2178 at bus_generic_new_pass+0xb0 #13 0xffff0000004f2178 at bus_generic_new_pass+0xb0 #14 0xffff0000004ecaec at bus_set_pass+0x50 #15 0xffff000000434be0 at mi_startup+0x1e0 #16 0xffff0000000008a8 at virtdone+0x68 armv8crypto0: CPU lacks AES instructions Timecounters tick every 1.000 msec usbus0: 5.0Gbps Super Speed USB v3.0 sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== ugen0.1: <(0x1106) XHCI root HUB> at usbus0 uhub0 on usbus0 uhub0: <(0x1106) XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command. sdhci_bcm0-slot0: ============== REGISTER DUMP ============== sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902 sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001 sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000 sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947 sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000 sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000 sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000 sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000 sdhci_bcm0-slot0: =========================================== mmc0: No compatible cards found on bus iicbus0: <OFW I2C bus> on iichb0 iic0: <I2C generic I/O> on iicbus0 mmcsd0: 64GB <SDHC SR64G 8.0 SN 2C31A197 MFG 10/2019 by 3 SD> at mmc1 50.0MHz/4bit/65535-block bcm2835_cpufreq0: ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF CPU 0: ARM Cortex-A72 r0p3 affinity: 0 Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG> Trying to mount root from ufs:/dev/ufs/rootfs [rw]... Instruction Set Attributes 0 = <CRC32> Instruction Set Attributes 1 = <> Instruction Set Attributes 2 = <> Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> Processor Features 1 = <> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA> Memory Model Features 1 = <8bit VMID> Memory Model Features 2 = <32bit CCIDX,48bit VA> Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8> Debug Features 1 = <> Auxiliary Features 0 = <> Auxiliary Features 1 = <> AArch32 Instruction Set Attributes 5 = <CRC32,SEVL> AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD> AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ> CPU 1: ARM Cortex-A72 r0p3 affinity: 1 CPU 2: ARM Cortex-A72 r0p3 affinity: 2 CPU 3: ARM Cortex-A72 r0p3 affinity: 3 gic0: using for IPIs Release APs...done TCP_ratelimit: Is now initialized WARNING: WITNESS option enabled, expect reduced performance. uhub0: 5 ports with 4 removable, self powered Warning: no time-of-day clock registered, system time will not be set accurately Dual Console: Serial Primary, Video Secondary ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0 uhub1 on uhub0 uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.21, addr 1> on usbus0 uhub1: 4 ports with 4 removable, self powered ugen0.3: <vendor 0x1ea7 2.4G Keyboard> at usbus0 ukbd0 on uhub1 ukbd0: <vendor 0x1ea7 2.4G Keyboard, class 0/0, rev 1.10/2.00, addr 2> on usbus0 kbd1 at ukbd0 genet0: link state changed to UP lo0: link state changed to UP genet0: link state changed to DOWN genet0: link state changed to UP ums0 on uhub1 ums0: <vendor 0x1ea7 2.4G Keyboard, class 0/0, rev 1.10/2.00, addr 2> on usbus0 ums0: 8 buttons and [XYZT] coordinates ID=2

As you can see I am trying 15.0 to see if I would had more chance, but got the same behavior with 14.0-RELEASE
 
You must log in or register to reply here.
Back
Top