Hostapd starts without wpa2 but doesn't start with wpa2. Have I forgotten something here?
pciconf -lv for the card I'm using:
rc.conf:
ifconfig for the device:
hostapd config in /etc/hostapd.conf
If I run hostapd /etc/hostapd.conf with the wpa security lines commented out:
(working!!!)
If I run hostapd when the lines wpa security lines are uncommented:
if the "#driver=rtwn0" is uncommented in hostapd.conf:
pciconf -lv for the card I'm using:
Code:
rtwn0@pci0:2:0:0: class=0x028000 rev=0x01 hdr=0x00 vendor=0x10ec device=0x8176 subvendor=0x10ec subdevice=0x8211
vendor = 'Realtek Semiconductor Co., Ltd.'
device = 'RTL8188CE 802.11b/g/n WiFi Adapter'
class = network
rc.conf:
Code:
hostname="satania"
keymap="se.kbd"
ifconfig_ue0="DHCP"
interface=wlan0
ifconfig_ue0_ipv6="inet6 accept_rtadv"
sshd_enable="YES"
ntpdate_enable="YES"
ntpd_enable="YES"
powerd_enable="YES"
# Set dumpdev to "AUTO" to enable crash dumps, "NO" to disable
dumpdev="AUTO"
zfs_enable="YES"
apache24_enable="yes"
#wireless
wlans_rtwn0="wlan0"
ifconfig_wlan0="DHCP"
create_args_wlan0="wlanmode hostap"
ifconfig for the device:
Code:
wlan0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 44:6d:57:0c:d1:e8
groups: wlan
ssid satania channel 6 (2437 MHz 11g)
regdomain FCC country US authmode OPEN privacy OFF txpower 30
scanvalid 60 protmode CTS wme dtimperiod 1 -dfs
parent interface: rtwn0
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
status: no carrier
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
hostapd config in /etc/hostapd.conf
Code:
interface=wlan0
#driver=rtwn0
ssid=satania
channel=6
hw_mode=g
macaddr_acl=0
auth_algs=3
## wpa security
#wpa=2
#wpa_passphrase="passphrase"
#wpa_key_mgmt=WPA-PSK
#wpa_pairwise=TKIP
#rsn_pairwise=CCMP
## disable invisibe mode
ignore_broadcast_ssid=0
If I run hostapd /etc/hostapd.conf with the wpa security lines commented out:
Code:
root@satania:/home/ove # hostapd /etc/hostapd.conf
Configuration file: /etc/hostapd.conf
Using interface wlan0 with hwaddr 44:6d:57:0c:d1:e8 and ssid "satania"
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
If I run hostapd when the lines wpa security lines are uncommented:
Code:
root@satania:/home/ove # hostapd /etc/hostapd.conf
Configuration file: /etc/hostapd.conf
Using interface wlan0 with hwaddr 44:6d:57:0c:d1:e8 and ssid "satania"
ioctl[SIOCS80211, op=7, val=5, arg_len=0]: Invalid argument
bsd_set_ieee8021x: Failed to enable WPA/802.1X
IEEE 802.1X initialization failed.
Interface initialization failed
wlan0: interface state UNINITIALIZED->DISABLED
wlan0: AP-DISABLED
wlan0: Unable to setup interface.
wlan0: interface state DISABLED->DISABLED
wlan0: AP-DISABLED
wlan0: CTRL-EVENT-TERMINATING
hostapd_free_hapd_data: Interface wlan0 wasn't started
if the "#driver=rtwn0" is uncommented in hostapd.conf:
Code:
root@satania:/home/ove # hostapd /etc/hostapd.conf
Configuration file: /etc/hostapd.conf
Line 2: invalid/unknown driver 'rtwn0'
1 errors found in configuration file '/etc/hostapd.conf'
Failed to set up interface with /etc/hostapd.conf
Failed to initialize interface