internet

I work from my laptop and I get Internet from my phone, but yesterday it stopped working, although I didn't do anything with it. Now I have dns names resolved, but the packets are not coming

I am currently not on FreeBSD I recently installed FreeBSD again I had this issue every time I have switched to FreeBSD in the past. I asked this question a couple of months ago but none of the answers worked. I decided to ask again maybe this time I can start using FreeBSD. The download speed...

/etc/jails.conf: firefox { path = "/root/jails/firefox"; ip4.addr = "10.0.0.201"; host.hostname = "firefox"; interface = "wlan0"; mount.devfs; allow.raw_sockets; exec.clean; exec.start = "/bin/sh /etc/rc"; exec.stop = "/bin/sh /etc/rc.shutdown"; } /root/jails/firefox/etc/resolv.conf...

Update 2023-12-20 This guide applies only to the VMware based "Virtual Server Cloud" VPS servers, which have been discontinued in mid 2023 and replaced with the "VPS Linux" servers. Due to problems with getting IPv6 to work reliably with the IONOS VPS, I have also updated the IPv6 Networking...

I used the default configuration file for Linux systems from ProtonVPN (for OpenVPN). I start OpenVPN once via the 'onestart' command, it then asks for the username and password. After this it connects, and it seems to connect correctly, but I have no internet and can't ping the google servers...

It becomes preinstalled with Gnome3 and possibly many others. So there is the command: pkg remove epiphany and then removing games maybe: pkg remove atomix pkg remove gnome-2048 pkg remove gnome-nibbles pkg remove gnome-chess pkg remove five-or-more pkg remove lightsoff pkg remove gnome-mahjongg...

Hi, I have recently setup a virtual machine for FreeBSD. I found that I was unable to connect to the internet, I was wondering how I can configure this inside a virtual machine. Thanks!

I get on bootup: ure0 on uhub 2 ure0: <Realtek USB 10/100/1000 LAN, class 0/0. rev 3.00/30.00. addr 8> on usbus0 miibus1: <MII bus> on ure0 rgephy1: <RTL8251/8153 1000BASE-T media interface> PHY0 on miibus1 rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 1000baseTX-FDX, 1000baseT-FDX...

I am running a FreeBSD EC2 instance with a single jail. In a regular homebrew setup, I would create a jail in "shared IP" (iocage) mode, and configure my router to forward various ports to the jail. In EC2, I am not sure whether to share the public IP or assign a new one. I created a new...

I use 1984hosting.com as my provider and want to install FreeBSD on the server. I can see that they have the operating system in the dropdown menu, so I do not have to download it myself. However, when I go through the installation I have to set up the internet connection. The information I have...

I have an Intel HM18025 V.92 56K Voice / Fax / Data internal Modem. It works perfectly fine with Microsoft Windows. However, my attempt to connect to my Internet Service Provider using BSD's 'ppp' Command fails. Upon entering Terminal Mode 'term' it gives the following message, and then goes...

For an assignment we have to connect two workstations to the internet through an HP server running BSD. The WS are connected to a switch that runs to eth0(10.0.0.0 network) and eth1 is connected to the schools internet 192.168.175.0 network. Gateway is enabled, the server is connected to the...

So I just installed FreeBSD in Dual Boot with Windows 10 and everything was fine during the install and during the install it downloaded the files it needed I have a wi-fi connection by the way. I looked at wpa_supplicant.conf and everything was right and I look at resolv.conf and here is what I...

I was trying to configure the mirror site for binary packages but couldn't get it as I wanted. The overseas internet connection here in Korea is very bad (about 50KB/s at best and down to 500B/s in actual download speed per connection) while the local connection is very fast (around 8MB/s per...

Hi! My name is Bogdan Nikolaev, i'm from Eysk, Russia. I'm writed small program for very easy configuring PPPoE connection - pppconf. What is works? Simple, pppconf ask few questions and create valid ppp.conf file. Program written in C and can be compiled using GCC at least version 4.2.1...

The problem I have is about the internet speed as I want to install certain programs repositories but I always download at a speed of 10kb when I have at least 4MB anyone knows what happens?